Old toilet removal
We shut off the water, drain the tank, disconnect the supply, and carry the old toilet out to the truck. You do not have to move it to the curb or pay a disposal fee. The bowl, tank, and seat all leave with us.
Code-correct installs, clean floors, no leaks, no callbacks
Toilet Installation Pocatello ID done right the first time
Toilet Installation Pocatello ID means pulling the old bowl, checking the flange and shut-off valve, setting a new wax ring, and testing every flush before we pack up. We handle everything from a standard 1.28 GPF swap to a comfort height toilet installation Pocatello Idaho for a family member who needs an easier seat height. If your toilet rocks, runs, or leaks at the base, we can usually get you on the schedule the same week.
Careful work. Honest options.
About this service
What Toilet Installation Pocatello ID Actually Involves
A proper Toilet Installation Pocatello ID job is more than dropping a new bowl on the flange. We shut off the water, drain the tank, pull the old toilet, and inspect the flange for cracks or rot. Then we scrape the old wax, check the closet bolts, set a fresh wax ring or waxless seal, and torque the bowl down level. We reconnect the supply line, check the fill valve and flapper, and run three full flush cycles before we call it done. Most standard swaps take 1 to 2 hours.
Pocatello homes run the gamut: 1920s bungalows near Old Town with cast iron drains, mid-century ranches in Highland Area, and newer builds out by Pocatello Creek with PEX already stubbed in. Older homes often need a new shut-off valve, a flange repair ring, or a short section of copper piping replaced while we are in there. If you have been searching toilet install Pocatello Idaho near me because the base is wet or the bowl rocks, that is usually a failed wax seal or a broken flange, and both are fixable in the same visit.
- ✓ Lower water bills
- ✓ No more floor rot
- ✓ Comfort height option
- ✓ Code-correct venting
What's included
What Our Toilet Installation Includes
Every install covers the full swap: removal, disposal, new seal, new supply line, and a flush test. If we find a problem under the old bowl, we quote it before we touch it. Here is what comes standard.
New wax ring and bolts
Every install gets a new wax ring or waxless seal and new closet bolts. We scrape the old wax off the flange, check the flange height, and add an extension if the flange sits below the finished floor so the seal compresses correctly.
New supply line
We replace the braided supply line on every job. Old lines crack at the ferrule and leak behind the toilet where you cannot see them. A new line and a checked angle stop cost us a few dollars and save you a flooded floor.
Flush and leak test
Three full flushes, a paper test, and a look under the bowl for any weep. We check the fill valve water level, the flapper seal, and the tank bolts. If anything drips, we fix it before we pack up the tools.
Silicone caulk at the base
We caulk the base with silicone caulk, leaving the back open so a future leak can drain out instead of pooling. That is the code-correct way to set a toilet, and it keeps mop water from getting under the bowl.
Walkthrough and haul-away
Before we leave, we show you the fill valve and flapper so you know what to check if the toilet ever runs. The old toilet goes in the truck, the floor gets wiped down, and you get a flat invoice with no add-ons.
How it works
How Our Toilet Install Process Works
Call or text us with the make and model you want, or tell us your budget and we will recommend one. We give you a flat price over the phone for a standard swap, including haul-away of the old toilet. No trip charge inside Pocatello city limits, and no surprise add-ons when we get there.
We lay drop cloths, shut the angle stop, flush and sponge out the tank, and disconnect the supply line. The old toilet comes up and out to the truck. We inspect the flange, the closet bolts, and the flooring around the base. This is where we find the cracked flanges and soft subfloor that caused the original leak.
We scrape the old wax, vacuum the flange, and set a new wax ring or waxless seal. If the flange is below the finished floor, we add a flange extension so the seal compresses correctly. New closet bolts go in, and we dry-fit the bowl to check for rocking before anything gets tightened down.
The new toilet goes down level, bolts get snugged in an alternating pattern so the bowl does not crack, and we reconnect the supply with a new braided line. We set the tank, adjust the fill valve to the right water level, and check the flapper chain. A quarter-turn of the angle stop confirms the shut-off holds.
Three full flushes, a paper test, and a look under the bowl for any weep. We check for rocking, caulk the base with silicone caulk, and wipe down the floor. The old toilet leaves with us. You get a walkthrough of the new fill valve and flapper so you know what to check if it ever runs.
STEP 01Phone quote
Call or text us with the make and model you want, or tell us your budget and we will recommend one. We give you a flat price over the phone for a standard swap, including haul-away of the old toilet. No trip charge inside Pocatello city limits, and no surprise add-ons when we get there.
Tools & methods
Tools and Methods We Use on Every Install
Pipe wrench and adjustable wrench
Used to break loose the supply line and the tank bolts without rounding the nuts. We keep a full set on the truck so we are not fighting a seized fitting with the wrong tool.
Plumber's snake
If the drain is slow or the toilet gurgles, we run a snake through the trap arm before the new toilet goes down. Better to find the clog now than after the new bowl is set.
Caulking gun with silicone caulk
We caulk the base of every toilet with silicone caulk, leaving the back open. That keeps mop water out from under the bowl and lets any future leak drain where you can see it.
Oscillating multi-tool
Used to cut stubborn closet bolts, trim a flange repair ring, or clean up old wax and caulk around the base. It gets into tight spots a saw cannot reach.
Laser level and stud finder
The laser level confirms the bowl sits flat. The stud finder locates framing if we are reinforcing the wall for grab bars or a heavier fixture near the toilet.
Moisture meter
We check the subfloor around the flange for hidden moisture. A meter catches a slow leak that has not stained the floor yet, so we can fix the decking before the new toilet goes down.
Real results
Before and after.
Toilet Installation
Cracked flange in a 1940s Old Town home
The original cast iron flange was cracked in two places and sitting a quarter inch below the tile. The toilet rocked, the wax ring had failed, and water had stained the subfloor around the base. The homeowner had been putting a towel down for a month.
After: We cut out the soft subfloor, installed a new flange at the correct height on top of the finished floor, and set a new comfort height Kohler with a waxless seal. Three flushes, no weep, no rocking. The whole job took about three hours.
Book this service →
Toilet Installation
Running toilet in a University Area rental
A 20-year-old toilet in a student rental ran constantly. The flapper was warped and the fill valve was scaled up from hard water. The water bill had climbed about $40 a month, and the landlord was getting complaints about the noise.
After: We replaced the flapper and fill valve the same day for a repair price. The toilet stopped running, the water bill dropped back to normal, and the tenant stopped calling. Total time on site was about 45 minutes.
Book this service →
Toilet Installation
Comfort height upgrade in Highland Area
A homeowner in Highland Area had a standard 15 inch toilet that was getting hard for her mother to use. The floor around the base was sound, but the shut-off valve was seized and the supply line was original. The bathroom had no grab bars.
After: We replaced the angle stop, installed a new braided supply line, and set a comfort height American Standard with the seat at 18 inches. We also reinforced the wall and installed two grab bars. The install took about two hours.
Book this service → Problems we solve
Toilet Problems We Fix in Pocatello
Most toilet calls come down to one of these. We diagnose the cause, not just the symptom, so the new toilet does not develop the same problem.
Ask a pro →Water pooling at the base of the toilet
We pull the toilet, inspect the flange, and set a new wax ring or waxless seal. If the flange is cracked or sitting too low, we repair it or add an extension so the seal compresses the way it should. Then we test three flushes before we leave.
Toilet rocks or shifts when you sit down
We pull the toilet, check the flange and the subfloor, and set the new bowl on a level surface. New closet bolts, a fresh seal, and a shim if needed. We caulk the base with silicone caulk so it does not move again.
Toilet runs constantly or refills on its own
If the bowl and tank are sound, this is a repair, not a replacement. We swap the flapper, fill valve, and sometimes the flush valve. If the toilet is 20 years old and parts are hard to find, we quote a new 1.28 GPF model instead.
Slow drain or gurgling after the flush
We check the trap arm and the vent stack while the toilet is up. If the drain line needs to be snaked or the vent is blocked, we handle it under our plumbing license. Then the new toilet goes down on a drain that actually works.
Proof you can check
Licensed, Insured, and Local
- State of Idaho Plumbing License · Idaho Division of Occupational and Professional Licenses
- EPA Lead-Safe Certified Firm · U.S. Environmental Protection Agency
- OSHA 10 and OSHA 30 · Occupational Safety and Health Administration
- ADA Compliance Certification · Certified Access Specialist program
- TCNA Tile Installation Certification · Tile Council of North America
Most standard toilet installs in Pocatello run $250 to $450 in 2026, including haul-away of the old bowl. That covers labor, a new wax ring, a new supply line, and silicone caulk. If we find a cracked flange, a bad shut-off valve, or soft subfloor, those repairs add $75 to $300 depending on what is needed. Comfort height and bidet-seat models do not change the labor price.
A standard swap takes 1 to 2 hours from shut-off to final flush test. If the flange needs repair or the shut-off valve is seized, plan on 2 to 3 hours. We schedule a two-hour window and call you 30 minutes before we arrive. You do not need to drain the tank or move anything; we handle all of that.
A straight like-for-like toilet swap in a single-family home does not require a plumbing permit in Pocatello. If we are moving the drain, adding a new fixture, or doing work in a commercial building, a permit is required and we pull it. We handle the inspection scheduling with Bannock County so you do not have to.
For most Pocatello homes, a 1.28 GPF comfort height two-piece from Kohler, American Standard, or Toto is the right call. Comfort height puts the seat at 17 to 19 inches, which is easier on knees. If you have a small bathroom, a round bowl saves about 2 inches of depth. If you want a quieter flush, a Toto with a 1.28 GPF gravity flush is the one we install most.
Ready when you are
Get Your Toilet Installation Pocatello ID Quote Today
Call BathFlow Remodeling for a flat price on your toilet install. We are a state-licensed plumbing contractor, we haul the old toilet away, and we test every flush before we leave. Same-week scheduling, and same-day service when your only bathroom is down.
Get a Quote +19863369053 →
Request an appointment
Contact our Pocatello bathroom crew
Call us or send a message and we will get back to you the same business day. We schedule estimates Monday through Friday and can usually get to a Pocatello address within a few days. Tell us what is going on with the bathroom and we will tell you what it takes to fix it.
Call anytime+19863369053Email the officeinfo@bathroomremodelpocatelloid.com
Office hoursOpen 24 hours · 7 days a week