Fixture Removal and Disposal
We pull the old vanity bar, ceiling globe, or sconces, cap the wiring safely, and haul the old fixtures away. No pile of dead lights left in your garage.
Bright, code-correct lighting for Pocatello bathrooms, big or small
Bathroom Lighting Installation Pocatello ID Done Right
Bathroom lighting installation Pocatello ID homeowners can count on starts with a proper layout, not a guess. We map light to your vanity, shower, and mirror, then wire it clean and to code. Whether you need a single vanity light install in Pocatello Idaho or a full recessed lighting installation Pocatello Idaho package, we get it bright, even, and safe.
Careful work. Honest options.
About this service
Bathroom Lighting Installation Pocatello ID Explained
Bathroom lighting installation Pocatello ID is the trade work of running new circuits, mounting fixtures, and aiming light where you actually use it: the mirror, the vanity, the shower, and the floor path at 2 a.m. We pull the old builder-grade bar light, check the box and wiring, then set new fixtures with a laser level so nothing sits crooked. Dimmers, GFCI protection, and a properly sized exhaust fan all get tied in while the wall is open.
Most Pocatello homes we walk into have one weak ceiling globe doing all the work. That leaves shadows on your face at the mirror and a dark shower corner. If you have been searching for bathroom lighting near me Pocatello and getting generic advice, here is the fix: layer the light. A vanity light installation Pocatello ID at eye level, two or three recessed cans over the wet zone, and a dimmer so 6 a.m. does not feel like an operating room.
- ✓ Even, Shadow-Free Mirror
- ✓ Lower Power Bills
- ✓ Code-Correct and Safe
- ✓ Dimmer Control You Will Use
What's included
What Our Bathroom Lighting Installation Includes
Every job is different, but a standard bathroom lighting install covers the items below. If you want to add a circuit from the panel or cut into a finished ceiling for new cans, we quote that as part of the same visit.
New Wiring and Boxes
New cable runs from the switch to each fixture, with old-work boxes cut in clean. We check the existing circuit load and confirm the breaker and wire gauge can carry the new fixtures.
Vanity and Sconce Mounting
Fixtures set level with a laser level, at the right height for your mirror and counter. We torque mounting screws and seal exterior penetrations so nothing works loose over time.
Recessed Can Installation
Housings cut into the ceiling, spaced evenly, with damp-rated trims in the shower zone. We check spacing with a laser level so the row reads straight from the doorway.
Dimmer and Switch Wiring
Dimmer matched to the LED driver so there is no flicker or buzz. We label the breakers and show you which switch controls which fixture before we leave.
Patch, Paint, and Cleanup
Drywall patched, texture matched, and paint touched up around new boxes. Floors covered during the work, and the room swept and wiped down at the end of the day.
How it works
How Our Lighting Install Process Works
We look at your bathroom, the existing switch legs, and the panel. You tell us how you use the room. We mark fixture locations on the wall and ceiling with tape so you can see the layout before anything gets cut. This takes 30 to 45 minutes.
We kill the circuit at the breaker, verify with a tester, then drop plastic and lay canvas over the vanity and floor. A stud finder and moisture meter tell us what is behind the drywall and whether there is a hidden leak near the shower before we open anything up.
New cable runs from the switch box to each fixture location. We cut in old-work boxes, drill through framing, and pull wire clean. If you are adding recessed cans, we set the housings now and check spacing with a laser level so the row is straight.
Vanity bars, sconces, and recessed trims go up. We level every fixture, torque the mounting screws, and seal exterior penetrations with silicone caulk. Dimmer and switch get wired and tested at this stage, and we confirm no flicker before closing anything.
Power back on, every fixture tested at full and dimmed. We show you the switch layout, hand over any spare bulbs or trim rings, and walk the room with you. Total on-site time for a standard bathroom runs four to six hours.
STEP 01Walkthrough and Plan
We look at your bathroom, the existing switch legs, and the panel. You tell us how you use the room. We mark fixture locations on the wall and ceiling with tape so you can see the layout before anything gets cut. This takes 30 to 45 minutes.
Tools & methods
Tools and Methods We Use
Laser Level
Sets a straight reference line for vanity fixtures, sconces, and rows of recessed cans. Keeps everything level and evenly spaced so the room reads intentional.
Stud Finder
Locates framing behind the drywall before we cut in old-work boxes. Prevents hitting a wire or a pipe and lets us anchor heavy fixtures into solid wood.
Oscillating Multi-Tool
Cuts clean openings in drywall for new boxes and recessed housings with minimal dust and no torn paper edges. Makes patching faster and cleaner.
Moisture Meter
Checks for hidden moisture near the shower and tub before we open a wall. If there is a slow leak, we find it before it becomes a bigger repair.
Caulking Gun
Applies silicone caulk around exterior penetrations and wet-zone fixtures. Keeps water out of the wall and finishes the install clean.
Circuit Tester
Confirms the breaker is off before we touch a wire, and verifies GFCI function after install. Safety step we never skip.
Real results
Before and after.
Bathroom Lighting Installation
Old Town 1940s Bathroom Refresh
A 5x8 bathroom with one 60-watt ceiling globe, a dark shower corner, and a mirror that threw shadows on the homeowner's face. The switch was a single-pole with no dimmer, and the ceiling had a water stain near the vent.
After: Two sconces at 38 inches on center, one damp-rated recessed can over the shower, and a new dimmer. Light output went from about 800 lumens to over 2,400. The ceiling was patched and painted, and the stain is gone.
Book this service →
Bathroom Lighting Installation
Highland Area Vanity Upgrade
A builder-grade 4-foot vanity bar with two 60-watt bulbs, mounted too high at 84 inches, leaving the counter in shadow. No dimmer, and the switch was across the room from the door.
After: A new 3-light vanity fixture at 78 inches, a second switch leg so the vanity and ceiling light run independently, and a dimmer rated for the LED bulbs. Counter light levels roughly tripled at the sink.
Book this service →
Bathroom Lighting Installation
Pocatello Creek Master Bath Layer
A large master bath with one central ceiling fixture and a dark tub alcove. The homeowner had added a floor lamp near the tub, which was a shock risk near water.
After: Four recessed cans on a dimmer, two sconces at the double vanity, and a damp-rated can over the tub. The floor lamp is gone. Measured light at the vanity went from 12 foot-candles to 45.
Book this service → Problems we solve
Bathroom Lighting Problems We Solve
Most Pocatello bathrooms we see have one of these four issues. Each one is fixable in a single visit, and each one gets worse if you wait.
Ask a pro →One dim ceiling light doing all the work
We layer the light: a vanity fixture at face height, two or three recessed cans over the wet zone and floor path, and a dimmer on the main circuit. The room reads bigger and brighter without adding fixtures you do not need.
Flickering or buzzing LED fixtures
We test the circuit, check the splices, and match the dimmer to the LED driver. In most cases the fix is a new dimmer rated for the fixture, and we confirm zero flicker at every dim level before we leave.
No GFCI protection near the sink
We install a GFCI receptacle or breaker on the bathroom circuit, test it, and label it. It is a small job that brings the room up to code and removes a real safety risk.
Foggy mirror and damp ceiling
We size a new exhaust fan to the room's cubic footage, wire it to its own switch, and pair it with damp-rated lighting. The mirror clears faster and the ceiling stays dry.
Proof you can check
Licensed, Insured, and Local
- State of Idaho Electrical License · State of Idaho
- EPA Lead-Safe Certified Firm · U.S. Environmental Protection Agency
- OSHA 10 and OSHA 30 Training · Occupational Safety and Health Administration
- ADA Compliance Certification · ADA Compliance Certification program
- ICC Certified · International Code Council
Most single-bathroom jobs run $350 to $1,400 in 2026, depending on fixture count and whether new circuits are needed. A straight swap of one vanity light is at the low end. Adding three recessed cans, a dimmer, and a new switch leg pushes toward the top. We give you a fixed price after the walkthrough, and there is no charge for the estimate.
Layered LED lighting works best here: a vanity fixture at face height, two or three recessed cans over the shower and floor path, and a dimmer on the vanity circuit. Aim for 2700K to 3000K color temperature so skin tones look natural. Skip the single ceiling globe, it leaves the mirror in shadow.
A standard single-bathroom install takes four to six hours on site. That covers removing old fixtures, running new cable, mounting new lights, wiring the dimmer, and testing. If we are cutting in new recessed cans through a finished ceiling or adding a circuit from the panel, plan on a full day.
Yes, for anything beyond swapping a bulb or a fixture on an existing box. New circuits, recessed cans, dimmers, and any work inside the wall require a licensed electrician and a permit in most cases. We carry a State of Idaho Electrical License, pull the permit, and handle the inspection so you are covered.
Ready when you are
Get Your Bathroom Lighting Installation Pocatello ID Quote
Licensed, insured, and local. Call us and we will walk your bathroom, mark the fixture locations, and hand you a fixed price the same day. Most jobs get scheduled within a week.
Get a Free Quote +19863369053 →
Request an appointment
Contact our Pocatello bathroom crew
Call us or send a message and we will get back to you the same business day. We schedule estimates Monday through Friday and can usually get to a Pocatello address within a few days. Tell us what is going on with the bathroom and we will tell you what it takes to fix it.
Call anytime+19863369053Email the officeinfo@bathroomremodelpocatelloid.com
Office hoursOpen 24 hours · 7 days a week